Copper Backsplash Installation Guide
Installing a Natuross copper kitchen backsplash is simple. Most customers choose adhesive mount and install directly over tile, drywall, wood, stone, or metal.
Your backsplash arrives as a finished, sealed panel, custom made to your selected size and finish. No sealing is needed before installation. Choose the installation method that fits your wall and your project.
1. Adhesive Mount
Most popular. Best for most copper kitchen backsplashes. Installs directly over tile, drywall, wood, stone, brick, or metal using construction adhesive, tile adhesive, silicone, or MS-polymer adhesive.
2. Screw Mount
Maximum strength. Best for very large panels, outdoor areas, fireplaces, brick, stone, or any place where extra mechanical support is preferred.
3. Hanging Wire
Decorative and removable. Best for wall art, signs, plaques, and decorative panels. For kitchen backsplashes, adhesive or screw mount is usually better.
Adhesive Mount, Most Popular
This is the easiest option and the method most customers choose for stove and kitchen backsplash panels. The panel installs like a wall tile, but it is one solid handmade metal panel instead of many small tiles.
- Make sure the wall is clean, dry, flat, and stable.
- Apply adhesive to the back of the panel only, not to the decorative front.
- Press the panel firmly into place and check that it is level.
- Use painter’s tape only to help hold alignment while the adhesive cures.
- Allow the adhesive to cure fully before cleaning or heavy use.
Adhesive mount works over existing tile, drywall, wood, stone, brick, or metal when the surface is properly prepared.
Screw Mount, Maximum Strength
Screw mount is the strongest installation method. It is recommended for very large panels, outdoor areas, fireplaces, masonry walls, or any installation where extra strength is desired.
- Hold the panel in position and mark the hole locations.
- Drill pilot holes. Use proper anchors if installing on drywall, tile, brick, stone, or masonry.
- Drive screws through the pre-drilled panel holes.
- Cover the screw heads with the decorative caps if included with your order.
The installer should choose anchors and fasteners suitable for the wall material.
Hanging Wire, Decorative and Removable
Hanging wire is best for decorative wall art, family name signs, house plaques, and panels that you may want to move later. It is not the main method we recommend for a permanent kitchen backsplash behind a stove.
- Install hooks, nails, or proper wall hangers at the correct spacing.
- Hang the panel using the attached wire or D-rings.
- Adjust until level.
Panel Details
- Material: real copper, real brass, or silver-plated copper/brass, depending on your selected finish.
- Metal thickness: 24 gauge, about 0.5 to 0.6 mm.
- Backing: rigid 4 mm composite backing.
- Total thickness: about 6 mm, close to 1/4 inch, similar to a wall tile.
- Finish: sealed with a clear protective coating for everyday kitchen use.
- Use: suitable for kitchen backsplashes, stove backsplashes, range areas, wet areas, outdoor areas, fireplaces, signs, plaques, and feature panels.
Heat and Stove Use
Natuross copper backsplashes are designed for use behind stoves and ranges. The clear protective finish helps protect the metal from everyday kitchen use, grease, moisture, and fingerprints.
The panels are heat-resistant, but they are not fireproof. Keep at least 2 inches of clearance from any open flame and always follow your appliance and local installation requirements.
Multi-Piece Backsplashes
If a backsplash is too large for one single panel, we make it as a multi-piece system. The main focal design, such as a tree, animal, medallion, or central artwork, is kept as one main piece whenever possible.
Side and border pieces are designed to match the center panel. Seams are placed at natural design breaks, not through the main subject.
Installation order: install the center focal panel first, then install the surrounding side or border pieces.
Installation FAQ
Can I install it over existing tile?
Yes. Most customers install directly over existing tile, as long as the surface is clean, dry, flat, and stable.
Do I need a special adhesive?
No special Natuross adhesive is required. Use a quality construction adhesive, tile adhesive, silicone, or MS-polymer adhesive suitable for your wall surface.
Do I need to seal the copper before installation?
No. Your panel arrives sealed with a clear protective finish. No sealing is needed before installation.
Can I install it myself?
Yes. Many customers install their backsplash themselves, especially with adhesive mount. Very large panels may be easier with two people.
Can it be used behind a gas stove?
Yes, it can be used behind gas stoves when installed with proper clearance. Keep at least 2 inches from any open flame and follow your appliance requirements.
Can I order a custom size?
Yes. If your exact size is not listed on the product page, send your width and height through live chat. We can add your custom size as a new option and send you the direct order link.
After Installation
Clean with a soft cloth, warm water, and mild dish soap. Do not use abrasive pads, harsh chemicals, or metal scrubbers.
The panel is made to be easy to live with. Grease and fingerprints wipe from the sealed surface during normal kitchen cleaning.
Shop copper kitchen backsplashes Browse designs Browse finishes See real customer installations